RPS1000-A3
8A outputs
S
3600 series
S3600-28P-EI
S
3600-52P-EI
S3600-28F-EI
R
ated voltage range: -48 to -60 VDC
0
404A054
S3610 series
S
3610-28P
S
3610-28TP
S3610-28F
S3610-52P
S5100 series
S5100-26C-EI
S
5100-50C-EI
S5100-24P-EI
S5100-48P-EI
S5500-EI series S5500-28F-EI, DC powered
RPS1000-A3
25A outputs
S3600 series
S
3600-28P-EI
S3600-52P-EI
S3600-28F-EI
R
ated voltage range: -48 to -60 VDC
0
404A055
S3610 series
S3610-28P
S3610-28TP
S3610-28F
S
3610-52P
S5100 series
S5100-26C-EI
S5100-50C-EI
S5100-24P-EI
S5100-48P-EI
S5500-EI series S5500-28F-EI, DC powered
S3100 series S33100-28TP-PWR-EI
Rated voltage range: -52 to -55 VDC 0404A053
S3600 series
S3600-28P-PWR-EI
S3600-52P-PWR-EI
S3600-28F-PWR-SI
S3600-52P-PWR-SI
S5100 series
S5100-26C-PWR-EI
S5100-50C-PWR-EI
S5120 series
S5120-28C-PWR-EI
S5120-52C-PWR-EI
S5500-SI series
S5500-28C-PWR-SI
S5500-52C-PWR-SI
S5500-EI series
S5500-28C-PWR-EI
S5500-52C-PWR-EI
S5600 series
S5600-28C-PWR
S5600-50C-PWR
S5500-EI series
S5500-28C-EI, DC powered
(-48 VDC interface)
Rated voltage range: -48 to -60 VDC 0404A053
S5600 series
S5600-26C
S5600-50C
S5600-26F
S5800 series
S5800-32C-PWR
S5800-56C-PWR
S5800-60C-PWR
4
REDUNDANT POWER SYSTEMS FOR H3C ENTERPRISE FIXEDCONFIGURATION SWITCHES
H3C SWITCHES WITH RPS SUPPORT (continued)
R
PS model Supported switch series / model number Switch DC input voltage range DC power cable code
Note:
• The RPS500-A3 and RPS 800-A can provide selective DC power supply to the powered device depending on the connected DC output cable(s).
• Currently, when working as an external power supply system for low-end Ethernet switches, RPS500-A3 or RPS800-A does not support
concurrent -50 V/ -54 V and +12 V outputs.
• The RPS1000-A3 can feed multiple devices at the same time. The number of powered devices that the RPS unit can support is jointly
determined by the power consumption of the powered devices and the maximum output power of the RPS unit. The total power consumption
contributed by all the powered devices must not exceed the maximum output power of the RPS1000-A3.
• The output of the RPS500-A3 or RPS800-A is controlled by a control pin. When the powered device’s own power supply system becomes fails, a
LOW signal is sent to the control pin of the RPS unit. Upon receiving this LOW signal, the RPS unit switches to the DC output state within 2 ms.
• For some models of powered devices, the control pin of the RPS500-A3 or RPS800-A can be controlled through a special cable to support hot
backup of power supply. Currently, the low-end Ethernet switches mentioned in this manual do not support this instance.
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals